Solenoid valve 1 inch dc24v main buyer country

When I see the request “solenoid valve 1 inch dc24v main country of buyer”, I immediately remember how many people make mistakes with voltage selection. DC24V is not just numbers, but a guarantee of stable operation under our voltage fluctuations. Especially in rural areas where there are problems with energy supply.

Why inch thread?

In projectsintegration of water and fertilizersI often encounter that customers confuse metric and inch threads. For 1-inch valves this is G1, but in the field sometimes you have to use adapters. I remember an incident at a construction site in the Krasnodar Territory, where I had to urgently order cone seals due to mismatched threads.

By the way,Shandong Linyao Intelligent Agriculture Technology Co.,LtdThe catalog contains special installation kits for such situations. But this does not always save - if the valve is already embedded in the system, it is easier to immediately take compatible fittings.

I can tell you from experience: inch threads more reliably hold pressure up to 16 bar, which is critical for drip irrigation. Although some colleagues argue that the metric is more convenient to maintain.

Voltage 24V DC - unobvious advantages

Working withremote valve control, was skeptical about DC24V at first. It seemed that 220V was more universal. But after an incident in a greenhouse complex near Voronezh, where half of the coils burned out due to a power surge, I revised my approach.

Now I recommend 24V for all projects withintelligent equipment. Especially in circuits where PLC controllers are used - signal matching is easier there. And safety is higher, which is important for agricultural enterprises.

By the way, on the website https://www.lyzhihuinongye.ru there are interesting cases on automation with exactly this voltage. In their projectsfrequency automatic equipmentprotection against polarity reversal is often included, which is rare among other manufacturers.

Features of installation in Russian conditions

Winter temperatures are the main enemysolenoid valves. Standard models with a brass body can withstand up to -15°C, but here in Siberia it can also be -40°. You have to either insulate it or use special designs.

Last year, at a facility in the Tyumen region, valves were installed in heated underground caissons. The solution is expensive, but cheaper than replacing cracked housings every spring.

CompanyShandong Lingyao Co.,Ltdoffers frost-resistant versions, but you need to clarify the parameters in advance. Their technical specialists usually recommend additional insulation of the coils - from condensation.

What problems do buyers face?

A common mistake is skimping on filters.Solenoid valve 1 inch dc24vquickly fails if there is not at least a coarse mesh filter in front of it. Especially with our water, where there is sand and scale.

One client in the Rostov region tried to save money on a filtration system - after three months three valves had to be replaced due to scale. The cost of repairs exceeded the savings by 4 times.

In projectswater filtration equipmentI always install two-stage cleaning before the valves. This increases service life by at least 40%.

Integration into smart agricultural systems

Now many customers are askingintelligent water and fertilizer integration equipmentwith the possibility of remote control. It is important to check protocol compatibility here.

At a facility in the Stavropol Territory, half of the circuit had to be redone due to the incompatibility of Modbus RTU and Profibus. Now I always test equipment for compatibility in advance.

UShandong Lingyao Co.,Ltdin the project descriptionssmart agricultural parksThere are ready-made solutions, but it is better to check the firmware versions. They update the software frequently without changing the labeling.

Service nuances

Spare parts are a headache for many. Coils onsolenoid valve 1 inch dc24vmust be in stock, otherwise a simple irrigation system during the season can cost hundreds of thousands of rubles.

I recommend always having a replacement set of coils and plungers. In the companyShandong Linyao Intelligent Agriculture Technology Co.,Ltdusually offer service contracts with a guaranteed supply of spare parts within 10 days.

From my own experience: it is better to overpay for service than to later look for compatible spare parts from other suppliers. Especially taking into account the sanctions restrictions.

Economic aspects of choice

Many people believe thatsolenoid valve 1 inch dc24v- a simple detail on which you can save money. But when calculating the cost of ownership, cheap models often lose out.

I compared valves from different manufacturers: budget options rarely have a service life exceeding 300,000 cycles, while professional lines have a service life of 1 million cycles or more. For irrigation systems, where valves operate 50-100 times a day, this is critical.

In projectshigh quality agricultural fieldsI always lay down equipment with a reserve resource. An overpayment of 15-20% upon purchase pays off in two seasons.